Description

The Abbycus rotating parts organizer provides up to 36 partitioned slots to store a variety of different items. The organizer is divided into six segments, each segment (module) consists of one to six partitioned bins which are all the same number by default. However, if you need a mix of modules please message us through Tindie with your desired configuration.

The organizer comes as an easily assembled kit and can be stacked to achieve multiple rotating layers. The basic kit contains two central hub flanges with pre-assembled bearing housing, desktop stand, six bin modules of your choice, and all required hardware. Additionally, the kit comes with self-adhesive rubber feet and a quantity of blank paper labels.

Features

• Strong and lightweight bins for small to medium size items. Six slot configurations to choose from.
• Easily replaceable paper labels.
• Stable tripod base can be hard mounted or even mounted upside down for under-table orientation.
• Uses quality ball bearings for smooth & quiet rotation.

Some Usage Examples

• Electronic assembly.
• Nuts, bolts, and other miscellaneous fasteners.
• Jewelry, sewing, macrame, nail art.
• Lapidary, model building, stamp collecting.
• And much more...

Dimensions

• Product dimensions: 33cm (13") diameter x 10cm (4") high.

Module Slot Dimensions (millimeters)

• 6 slot bin: L=65, W=24, H=17 to 55 tapered.
• 5 slot bin: L=65, W=29, H=17 to 55 tapered.
• 4 slot bin: L=65, W=38, H=17 to 55 tapered.
• 3 slot bin: L=65, W=50, H=17 to 55 tapered.
• 2 slot bin: L=65, W=77, H=17 to 55 tapered.
• 1 slot bin: L=65, W=150, H=17 to 55 tapered.

What is Included in the Kit?

• 6 bin modules of your choice (1 - 6 slots / bin module).
• 1 tripod stand with embedded nut.
• 1 short threaded rod, M6 x 9.5cm (used for single stack).
• 1 long threaded rod, M6 x 17cm (used for stacking two kits).
• 2 M6 x 12mm long nuts.
• 2 190mm flanges with pre-assembled bearings and housings.
• 1 55mm x 10mm flange spacer cylinder.
• 1 40mm clamp knob.
• 25 M3 x 10mm Phillips pan head screws.
• 100 blank paper labels 20mm x 15mm.
• 4 self adhesive 20mm diameter rubber feet (1 spare).

Assembly Directions

Please Note: There are two threaded rods in the kit. Use the short rod when a single level organizer is desired. The longer rod is used when stacking two kits together.

Single Layer Configuration:

1) Screw the threaded rod into the tripod base and tighten finger tight. Then Screw a 12mm long nut onto the threaded rod and tighten against the base using a wrench or pliers.

2) Place one flange over the threaded rod with the bearing housing facing downward. The place the 55mm spacer over the threaded rod.

3) Add the other flange with the bearing housing facing upward. Then screw the 40mm knob to the top and tighten.

4) Begin fastening the bins around the perimeter of the hub using the supplied M3 x 10 pan head screws. Leave the screws loose until all bins have been mounted. Then tighten all screws on the top and bottom.

Stacked Configuration:

This describes stacking two kits together to form a multilevel rotary organizer.

1) Assemble the first kit as described above but use the longer threaded rod in step 1.

2) Assemble the second rotary bin wheel.

3) Place the lower wheel and secure with an M6 long nut.

4) Place the upper wheel on the threaded rod and secure with the 40mm knob.

Add rubber feet and labels. Done!

What's Next?

We will be offering tool holder modules in the near future. Please let us know if you have other requirements.

Volume pricing and custom designs are available.

Questions or Suggestions

Please message us through Tindie 'Contact Store'.