Four Digit Nixie Clock with 5750 nixie tubes

Name: Four Digit Nixie Clock with 5750 nixie tubes
SKU: 11310
Price: 175.00 USD
Availability: InStock

Homemade six-digit Nixie Clock, made with IN-14 nixie tubes, RGB led underlighting, user selected. GPS driven time set. Fully assembled.

Designed by Oscilloscope clocks in United States of America

Four Digit Nixie Clock with 5750 nixie tubes 1

Four Digit Nixie Clock with 5750 nixie tubes 2

Four Digit Nixie Clock with 5750 nixie tubes 3

Four Digit Nixie Clock with 5750 nixie tubes 4

Four Digit Nixie Clock with 5750 nixie tubes 5

Four Digit Nixie Clock with 5750 nixie tubes 6

Four Digit Nixie Clock with 5750 nixie tubes 7

Four Digit Nixie Clock with 5750 nixie tubes 8

Four Digit Nixie Clock with 5750 nixie tubes 9

Four Digit Nixie Clock with 5750 nixie tubes 10

Four Digit Nixie Clock with 5750 nixie tubes 11

Four Digit Nixie Clock with 5750 nixie tubes 12

Four Digit Nixie Clock with 5750 nixie tubes 13

Buy with confidence.

Our Tindie Guarantee protects your purchase from fraud. Learn More

This is a store featuring my homemade electronic novelty clocks, made using obsolete electronic tubes, and my kits designed for diy for these clocks.

Homemade six-digit Nixie Clock, made with IN-14 nixie tubes, RGB led underlighting, user selected. GPS driven time set. Fully assembled.

This a fully assembled product (not a kit), made in the USA. GPS option so time & date are extracted from GPS or network and will set automatically. WiFi option will extract time & date from your net…

Instructions for Nixie clock

Note

To set the time

When plugged in, the LEDs should light immediately, and the display will read 11:11 for five seconds.
To enable GPS to auto set the time (if equipped), press fast set once and the display will change to 33:33.
To select a time zone (for GPS), press the TOGGLE button and the middle tubes will display “01”.
Press fast set to cycle through the time zones. When the correct number corresponding to the time zone needed
is selected from the list below, press slow set twice to return to set up.
The display will change after a few seconds to 00:00.
To enable the calendar to display, press toggle once, and the display will change to 22:22 for three seconds.
This means the calendar has been enabled.
Next the display will read “11:11” while the firmware detects the frequency automatically (60HZ, 50HZ or 1PPS)
The tubes should then display 1:11 for three seconds for 60HZ, or 0:00 for 50HZ or 4:44 for 1PPS.
If the wrong frequency was erroneously detected, unplug, wait until the leds go out, and then plug back in.
Next the tubes should display: 12 (12 hour format, the default setting) for three seconds.
To choose 24 hour format, press the fast set button once, and the display should be: 24 for three seconds,
then the display will show 1:00 (or 12:00 if 12 hr. format) and normal time keeping begins.
The set buttons operate as fast set / slow set, (hours / minutes).
*If the gps auto set is enabled, the time and date will be set automatically at this point.
*If equipped with the WifiModule, please follow the setup instructions below.

To program the preset on/off times from normal timekeeping mode

Press both buttons and the display will blank.
Press the fast set button to increment hours to the desired on time (:1 after the hour indicates AM, :0 indicates PM)
Press slow set to confirm your choice, and the hour you selected will appear with :00 for PM, :11 for AM.
To set the alarm for this time, press fast set again, and “1” will be displayed on the last nixie. (xx:xx:x1 )
Please refer to youtube for illustration: alarm demo
Press either button once to enter the OFF time set mode.
Follow the same procedure, and after the OFF time is confirmed (: XX appears after the hour selected), press slow set button to enter normal timekeeping (fast set, slow set) mode.
To program a second set of sleep / wake times, press fast set and repeat the procedure for a second time.

Please refer to the youtube link for illustration: 2nd on/off times setup demo

Note: The clock will display 12:00 AM to start (1:00 AM if in 24HR mode) so if the present time is afternoon, you will need to advance the time past 12:00 in order to reach the PM hours (if in 12 HR mode) else the preset on/off times may be reversed. I.E.: if the present time is 8:00 PM, you need to advance PAST 8:00 once, then stop at 8:00. If GPS equipped, time will set automatically.

Setup for the Wifi Module

After plugging the clock in, check available networks using your device, you should see an access point named “WifiModule”.
After disconnecting from any other network, connect to the Wifi Module.
Open your browser and type 192.168.4.1 in the address bar and press enter or go to bring up the Connect page.
Enter your SSID (network name) and password and click “submit”.
The confirmation page will appear and WifiModule will connect to your network. Time & date will set automatically.
If you need to erase the saved name & password, please unplug the clock for ten seconds, then hold down the “reset” button on the WifiModule and plug the clock back in. The led on the WifiModule should light.