1.Introduction:

RCN-1 is a DC 9V-12V Infrared Remote Control DIY Kit. User can use any infrared remote controller to control the lamp on or off with 18pcs white LED.

2.Feature:

• 18pcs highlight LED
• Perfect simple circuit
• Two position brightness control
• DIY hand soldering
• Infrared Remote Control

3.Parameter:

• Product Name:RCN-1 IR Control Lamp DIY Kit
• Product Number:RCN-1
• Work Voltage:DC 9V-12V
• Work Current:30mA
• Power Type:5.5mm Power Socket or 9V Battery(Not Included!)
• Work Mode:Switch or Infrared Remote Control
• Color:White LED
• Work Temperature:-40℃~85℃
• Work Humidity:5%~85%RH
• Size(Installed):656536mm

4.Function:

• S1 black button is used to turn ON or OFF lamp.
• S2 self-locking switch is used to change led brightness. 12pcs LED turn ON or 18pcs LED turn ON.
• Any infrared remote controller to control the lamp on or off.

5.Installation Tips:

• User needs to prepare the welding tool at first. Please wear anti-static gloves or anti-static wristbands when installing electronic components.
• Please be patient until the installation is complete.
• The soldering iron can't touch the components for a long time(1.0 second), otherwise it will damage the components.
• Pay attention to the positive and negative of the components.
• Strictly prohibit short circuit.
• User must install the LED according to the specified rules. Otherwise some LED will not light.
• Install complex components preferentially.
• Make sure all components are in right direction and right place.
• Check that all of the LED can be illuminated.
• It is strongly recommended to read the installation manual before starting installation.

6.Installation Steps(Please be patient):

• Step 1: Install 4pcs 330ohm Metal Film Resistor at R5-R8.
• Step 2: Install 2pcs 1Kohm Metal Film Resistor at R2,R3.
• Step 3: Install 1pcs 10Kohm Metal Film Resistor at R4.

• Step 4: Install 1pcs 15Kohm Metal Film Resistor at R1.

• Step 5: Install 18pcs LED at D1-D18.The longer pin is inserted into the rectangular pad(positive pole). The shorter pins are inserted into the round pads.

• Step 6: Install 2pcs 0.1uF 104 Ceramic Capacitor at C1,C2.
• Step 7: Install 1pcs TO-92 78L05 Voltage Regulator at U3.

• Step 8: Install 2pcs TO-92 S8050 Transistor at Q1,Q2.

• Step 9: Install 1pcs DIP-16 CD4017 IC at U1.There is a mark on one end of the IC and there is a mark on PCB where the IC can place on.These two marks are corresponding to each other and are used to specify the installation direction of the IC.

• Step 10: Install 2pcs 10uF 25V Electrolytic Capacitor at C3,C4.Pay attention to distinguish between positive and negative.The Longer pin is positive pole.The longer pin is inserted into the rectangular pad.
• Step 11: Install 1pcs 6610mm Black Button at S1.

• Step 12: Install 1pcs TO-92 78L05 Voltage Regulator at U2.

• Step 13: Install 1pcs 5.8*5.8mm Self-locking switch at S2.

• Step 14: Install 1pcs 5.5mm DC Socket at J1 on another side.
• Step 15: Install 4pcs M310mm and 4pcs M320mm Nylon Column on PCB.
• Step 16: Install 1pcs 9V Battery socket at DC 9V. Note: Red wire connect to ‘ + ’ .
• Step 17: Install 9V battery(not included) and then place lamp on plastic shell.Then press button to switch lamp.