Breakout board for GPS timing receiver module
Designed by Geppetto Electronics in United States of America
Buy with confidence.
Our Tindie Guarantee protects your purchase from fraud. Learn More
The store will be closed November 23th through December 8th.
The store will be closed January 1st through April 5th.
What is it? This is a breakout board for the SkyTraq Venus838LPx-T Timing GPS receiver. It's available with a SIP header that's "mostly" pin compatible with the AdaFruit Ultimate GPS breakout board, …
Read More…This is a breakout board for the SkyTraq Venus838LPx-T Timing GPS receiver. It's available with a SIP header that's "mostly" pin compatible with the AdaFruit Ultimate GPS breakout board, or with a DIP header that mates with the left-hand side of the Raspberry Pi GPIO header.
Timing modules operate differently from navigation modules. The Venus838LPx-T module performs a survey to determine its 3D location and then operates under the assumption that its location is fixed. Because of that, it can optimize its solutions for accuracy of time, providing precise timing information even with less than optimal satellite reception.
The pinout of the SIP board's 9 pin connector was chosen to be largely compatible with the AdaFruit Ultimate GPS module. The differences are:
The SIP variant breakout board provides a 9 pin .1" SIP header. The header provides LVCMOS (3.3v) level serial I/O for the NMEA data and command stream. The receive data pin is 5 volt tolerant (unlike the bare module). The power supply input can accept 5 volts and will generate 3.3v with an on-board LDO. The 3.3v pin can supply a small amount (perhaps up to 100 mA) of 3.3v power. Alternatively, if you wish, you can leave the Vin pin disconnected and supply regulated 3.3v power on the 3.3v pin. The antenna is supplied 3.3 volt power. An active antenna is recommended.
The Raspberry Pi board's header is intended to mount over the first 16 pins of the Pi's GPIO header. It's wired so the the GPS module is powered from the 3.3 volt supply from the Pi. The antenna power is obtained from the 5 volt supply pin. The UART pins are connected to GPIO 14 and 15 (the serial port) and the PPS pin is connected to GPIO 18.
The breakout board comes a supercap to provide short-term retention of the almanac and time to facilitate warm-starting. The cap will allow the module to warm-start if power is lost for less than about 3/4 of an hour.
The onboard LED is on when no fix is available and blinks at 1/2 Hz once a fix is established (this is in contrast to the LED driven by the PA6H module, which blinks at 1/2 Hz when there is no fix and is mostly off when there is one).
There is a test point on the SIP board connected up to the "P1PS2" pin of the module. This pin can be configured for a 10 MHz output nominally phase locked to GPS time (be aware, though, that the stability of this output is not comparable to a proper GPS disciplined oscillator).
If desired, the module can be purchased with an amplified patch antenna with a short cable terminated in a U.FL connector. This antenna will work adequately outdoors, in a South-facing window with a sky view, or in lightly constructed buildings, but a proper outdoor antenna is recommended.
The Venus838LPx-T module will provide PPS quantization error correction messages, allowing you to remove the quantization error present on the PPS output. Without correcting this error, the PPS will have approx. ±6 ns of jitter. With correction, the jitter can be reduced and the PPS accuracy can be as good as GPS can provide. The Allan deviation of the PPS output has the expected characteristic for a GPS receiver: at tau 1s it is about 10E-8 and the graph is a nearly straight line at a decade per decade reduction from there (10E-9 @ 10s, 10E-10 @ 100s, etc).
Navigation modules can provide excellent timing results, but require optimal satellite reception to do so. When a navigation receiver is presented with less than perfect conditions, the timing accuracy will suffer even more than the navigational accuracy. Timing receivers with their different optimization can retain timing accuracy even under conditions where navigational accuracy would suffer.
No country selected, please select your country to see shipping options.
No rates are available for shipping to .
Enter your email address if you'd like to be notified when GPS Timing module breakout can be shipped to you:
Thanks! We'll let you know when the seller adds shipping rates for your country.
Shipping Rate | Tracked | Ships From | First Item | Additional Items |
---|---|---|---|---|
:
|
Due to VAT regulations, orders to the UK must now be a minimum of £135 or include recipient VAT number.
Orders to the EU should include recipient's VAT number, if available, to avoid delivery delays.
Other international customers: Import duties, taxes and all other fees are the recipient's responsibility. Returned shipments will be either retried at customer expense or refunded minus shipping charges.
Product: (5.00)
Documentation: (4.40)
Shipping: (4.40)
Communication: (5.00)
Neal | Nov. 16, 2020
Alejandro | May 17, 2019
Paul | May 15, 2018
Clive | Oct. 24, 2017
David | Oct. 15, 2016
Buy with confidence.
Our Tindie Guarantee protects your purchase from fraud. Learn More
Farmington Hills, MI, United States of America
Ships from United States of America.
163 Reviews | 2,364 Orders
$12.50
Free Shipping!
$22.50
Free Shipping!
$12.49
Free Shipping!
$109.95
Free Shipping!
$40.00
Free Shipping!
$304.99
Free Shipping!
$159.99
Free Shipping!
$25.00
Free Shipping!
$21.70
Free Shipping!
$49.00
Free Shipping!
$29.50
Free Shipping!
$5.75
Free Shipping!
By clicking Register, you confirm that you accept our Terms & Conditions
We recognize our top users by making them a Tindarian. Tindarians have access to secret & unreleased features.
We look for the most active & best members of the Tindie community, and invite them to join. There isn't a selection process or form to fill out. The only way to become a Tindarian is by being a nice & active member of the Tindie community!