Ethernet Shield (10/100) for ESP32 boards
Designed by TwilightLord's in United States of AmericaSign up to get notified when this product is back in stock!
Ethernet Shield (10/100Mbps) for ESP32 boards Living in a condo building with heavily congested WiFi channels was causing issues when trying to control individually addressable LED strips over E1.31,…
Read More…Living in a condo building with heavily congested WiFi channels was causing issues when trying to control individually addressable LED strips over E1.31, especially notable when running audio reactive effects with high frame rates. The solution, a good old cable ethernet connection. To be able to my reuse all TwilightLord-ESP32 boards and the many D1 Mini32 ones that I have, I decided to design a shield to be able to stack it on top (or below).
Big shout-out to the developers of WLED and LedFX which sparked my interest in the world of addressable LEDs and audio reactive. Please consider donating to their projects if you are using them.
If you are looking for a great Shield for your WLED ESP based projects, I highly recommend looking at the WLED Wemos Shield by Serg74. You can order his PCBs and assemble it by yourself or buy one from his Tindie store
TwilightLord-ESP32 Ethernet Shield is a small form factor board that adds 10/100Mbps Ethernet to your ESP32 projects. It can be used with any ESP32 based project so as long the pinout described below is free in your project, yes running Ethernet on an ESP32 requires a lot of pins. It also works as a Shield to a D1 Mini32 (like MH-ET LIVE MiniKit for ESP32) or compatible board like my TwilightLord-ESP32 8MB and 16MB boards.
Shield on a MH-ET LIVE MiniKit for ESP32 board (not included). NOTE: Align the modules so that the first pins for every column starting from the USB side are skipped.
Shield on a TwilightLord-ESP32 board (not included)
Board is powered with 5v to the 5v0 pin and it has an onboard LDO 3v3 regulator to power the LAN7820 IC.
Bottom View (component side) RJ45 at the bottom
| GND | -- | -- | GND | |||||
| IO27 | -- | -- | GND* | |||||
| IO25 | IO22 | IO26 | -- | |||||
| -- | IO21 | IO18 | -- | |||||
| -- | IO17 | IO19 | -- | |||||
| -- | -- | IO23 | -- | |||||
| -- | GND | IO5 | -- | |||||
| -- | 5v0 | -- | -- | |||||
| -- | -- | -- | -- |
-- NC (not connected)
Top View (over RJ45) RJ45 at the bottom
| GND | -- | -- | GND | |||||
| GND* | -- | -- | IO27 | |||||
| -- | IO26 | IO22 | IO25 | |||||
| -- | IO18 | IO21 | -- | |||||
| -- | IO19 | IO17 | -- | |||||
| -- | IO23 | -- | -- | |||||
| -- | IO5 | GND | -- | |||||
| -- | -- | 5v0 | -- | |||||
| -- | -- | -- | -- |
-- NC (not connected)
Most of the pins are fixed by the ESP32 Ethernet implementation and cannot be changed. Bear in mind the pins on the table below will not be available to your ESP32 projects if the Ethernet is enabled.
| GPIO | USED BY | COMMENTS |
|---|---|---|
| GPIO5 | Power on/off | Active High signal to power on the LAN7820 IC |
| GPIO17 | RMII Clock | 50 MHz Clock sourced from ESP32 APLL |
| GPIO18 | PHY MDIO | |
| GPIO19 | ETH TXD[0] | |
| GPIO21 | ETH TX_EN | |
| GPIO22 | ETH TXD[1] | |
| GPIO23 | PHY MDC | |
| GPIO25 | ETH RXD[0] | |
| GPIO26 | ETH RXD[1] | |
| GPIO27 | ETH CRS_DV |
When configuring your ESP-IDF or Arduino projects please take the following into account:
If you are using ArduninoEspressif32 ETH library below are the values that must be used when configuring it:
/i/473872/products/2021-03-14T02%3A22%3A03.059Z-TwilightLord-ESP32-ETH_SHIELD-v1.0r1-002.png?1615659736)
ETH.begin(
(uint8_t) phy_addr, # 0
(int) power, # 5
(int) mdc, # 23
(int) mdio, # 18
(eth_phy_type_t) type, # ETH_PHY_LAN8720
(eth_clock_mode_t) clock_mode # ETH_CLOCK_GPIO17_OUT
);
Sign up to get notified when this product is back in stock!
