Saulius | Dec. 8, 2020

Good case for NanoVNA V2 Plus

For Case for the Nano VNA V2

Nicely made case for NanoVNA V2 Plus.
The corner joints could be more sturdy and joining stiffer.
Moreover would be helpful to have holes for the battery level LEDs.
Thank you!

Response from Blackmagic | Dec. 9, 2020

Hello Saulius,

thank you very much for the feedback. I am glad you liked it.

Greetings to Lithuania 🇱🇹 👍

Johannes | Nov. 1, 2020

Very good!

For Case for the Nano VNA V2

The case is well made and stable. Also easy to disassemble again. The NanoVNA2 fits perfectly in it. thank you!

Response from Blackmagic | Nov. 1, 2020

Hi Johannes, thank you very much for your review and purchase. 👍

Massimo | Sept. 18, 2020

Well done, but some size issue.

For Case for the Nano VNA V2

The case is well done and easy to assembly on the nanoVNA2 frame, but the side placed three buttons window and the power switch window must be adapted to fit the buttons and switch sizes.
I decided to keep the original nanoVNA2 front and back plates to get the device in/out ports information handy, I did it by making the holes fitted the original screws position. Because of that I had to trim the display frame border since it pushed the resistive touchscreen once the screws were tighten, locking the touchscreen function. Of course this issue arised just because I added the screws, it's not a case issue indeed.
I also had to add the 4 missing holes in front of the battery level LEDs on the power switch side, despite these holes are non essentials, they are very useful to monitoring the battery level status and its eventual charging activity.

Response from Blackmagic | Oct. 3, 2020

Great review Massimo, than you very much. 👍

Massimo | Sept. 18, 2020

Well done.

For Case for the Nano VNA

The case is well done, everything fits the right place.
Easy to assembly in the nanoVNA original frame.

Response from Blackmagic | Oct. 3, 2020

Massimo, thank you for your review, wish you all the best. 👍

Giuseppe | Aug. 1, 2020

Good productd. Made in 3D printing

For Case for the Nano VNA V2

The cover is nice. Is made in 3D printing. If injection plastic had been made it would have been the perfect solution

Response from Blackmagic | Aug. 1, 2020

Ciao Guiseppe, thank you, I'm glad you like it. 👍

Mathias | July 31, 2020

good fitting case the the Nano VNA

For Case for the Nano VNA V2

The case consists of two pieces that are 3D-printed. They match quite well at the joint at give a good fitting case for the Nano VNA.

Response from Blackmagic | July 31, 2020

Thank you Mathias for the great review.

Wayne | July 30, 2020

Correction necessary

For Case for the Nano VNA V2

I had a problem when trying do an install of a part to my VNA , however I got very fast help and direction from them. So this is to revise a negative first report.

Response from Blackmagic | July 31, 2020

Thank you Wayne, the small issue was that your VNA had front and back plates, these are not needed and can be screwed easy off.😃

Timothy | June 3, 2020

Works perfect

For Case for the Nano VNA V2

The case works perfectly. I don't know if this case will come apart again without cracking -- I haven't tried. Thanks for the great design.

Response from Blackmagic | July 31, 2020

Of course the case can be disassembled again, only a sharp knife is need and one can pry the parts open. I have tested many time and optimized the corner joints.
Thank you very much for your purchase and the great review. 👍

Vojtech | May 18, 2020