Wilhelm | Feb. 7, 2023

Potential nice Device

For ESP32-VS1053 MP3 Player & Web - Internet Radio

I had to wait very long to get it.
No Documentation comes with it.
I had it find it somewhere in the Internet.

https://github.com/donnersm/EdisonRadio/blob/main/Documentation/manual1.0.pdf
https://electronoobs.io/project/534#
https://www.hackster.io/mark-donners/edison-radio-best-internet-radio-esp32-arduino-4a80a5

For the moment i am stuck to compile, there is a SD.h to include, but here is a problem to find the correct file to compile without error.
Is there somebody to help, where to find the correct SD.h File?
Would be very nice to get a helping answer.

Response from JasonKits | April 25, 2023

Hi

Please send me a pm so as i can assit you and solve all your issues !

Radio board comes pre programmed and all you need to do is to connect via wifi and configure the stations

Regards
Jason

Jeffrey | Sept. 17, 2021

Don't know what I purchased

For Si5351 - 3 CHANNEL SIGNAL GENERATOR with SWEEP

In my dismay I didn't write down the exact numbers but I get square waves until I get the frequency high enough then I see a sine wave. Documentation doesn't say much at all.

Response from JasonKits | Sept. 17, 2021

The si5351 is a programmable oscillator which produces a square wave on all three channels. If a sine wave output is required one can use an L/C/R filter to smooth the output and cut down any harmonic. With a Suitable L/C filter the output is very stable .

Philippe | Nov. 6, 2020

Mark Peter | Sept. 14, 2020

Not a real product yet

For SMD Reflow HOT Plate Controller

The PCB seems to have missing components, at least an amazing amount of blank component pads. No mounting holes in the PCB! The schematic in the manual seems to differ from the received PCB. As it is, this product causes more trouble instead of solving an issue. I'm dissapointed.

Response from JasonKits | Sept. 14, 2020

Hi

I am sorry that you feel disappointed. The board is supplied as a basic hot end controller. it has extra features which are not yet supported. Mainly

Accepts 2 mote sensors
reset switch
buzzer control
fan control
Thermocouple support -

If you wish these features just drop me an email and I will be happy to supply you with a board with such features after I implement them in software.

Brian | Nov. 9, 2018

Good concept, but QC issues.

For 3DPrinter Filament Diameter Width Sensor Assembled

I bought this a while back and just now getting around to trying it out. Instructions needs to be improved, especially when using with the supplied LCD board. The main gripe is the path for the filament, it is too small. I barely got a 1.5mm rod through the guide. When you pay a good price for this, the product should be tested before sent to the customer. Yes, they give you the stl file, so be prepared to modify and reprint the filament guide piece. Also when buying the kit with the LCD board, there should be a header that would connect the sensor to the LCD board (with a voltage regulator for the 5V sensor).

Response from JasonKits | Nov. 11, 2018

Thanks for your feedback.

I always check the 3d printed part - if you need a replacement just let me know .

i have added the option to select the 3d part now .

Daniel | July 20, 2018

1 st board failed immediately.

For 3D Printer Filament Joiner/Fuser PID Controller

1st board failed immediately. Absolutely followed the included instructions exactly (very easy to hook up). The LCD lite up and started the count down, then a puff of smoke and it died .Contacted Jason on July 20th who said he would replace after testing his on hand stock for two days. It is now 8/16/2018. The replacement Jason claims he sent out has still not arrived. I will give a complete review after I receive and test the replacement

Response from JasonKits | July 21, 2019

Replacement board was sent and worked as it should. Daniel Update your review!